Setting up A Bathtub
Setting up A Bathtub
Blog Article
Right here down the page you will find lots of really good content related to How to Install a Bathtub.
Mounting a tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a brand-new one is likewise a reasonably challenging task. If the old bathtub is readily easily accessible, the project can relocate speedily; if you need to open up a wall to get rid of the old tub as well as position the new bathtub, the task is a lot harder. In either situation, the task is within a house handyman's skills, although you will certainly require a helper to move out the old bathtub and also embeded in the new one. Make certain you have qualified on your own for the task and are comfortable trying it. Rather than employing a service provider to take over a halfway-completed task, it is better to take into consideration employing one prior to you begin. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly aid you mount a new tub in your washroom if you have currently acquired a new bathtub and don't require to change the plan of your previous supply of water pipelines.
Your devices and material list should comprise the following:
Planning for the Installation
Firstly, the sustaining frame supplied with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is very important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets device to stop pressure on the bathtub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the outlet through the hole in the bath. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Ensure you use all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be suited its last setting.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installment, after that the first thing you must do is detach the water system. After doing so, turn on the taps to drain any kind of water staying in the system. The process of removing the existing taps can be fairly bothersome because of the restricted access that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a cloth all set for the staying water that will come from the pipelines. As soon as the supply pipes have actually been gotten rid of, use the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to quit the solitary taps from turning throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Installing the Tub
Using both wooden boards under its feet, position the bathtub in the called for setting. The wooden boards are practical in uniformly spreading out the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also changing the feet on the bath tub up until the level reads level.
To install faucets, fit the bottom of the furthest flexible faucet adapter to the proper supply pipeline by making a compression join; after that do the exact same for the various other tap.
Turn on the water supply as well as check all joints as well as brand-new pipework for leaks as well as tighten them if necessary. Fill up the bath tub and likewise examine the overflow outlet as well as the normal outlet for leakages.
Finally, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling and securing around the bath tub ought to wait till the bathtub has actually been used a minimum of when as this will resolve it into its final placement.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will certainly need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will need minimizing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin making sure that the washing machines are in place between the tap as well as the sink. Protect the faucet in position with the manufacturer offered backnut. When the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The former type should be connected to the tap ends first, tightening only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall in between the bathroom and also the tiling, bring about problems with moisture and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealants to blend in your components and also installations. They are offered in tubes and cartridges, and can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill, you can load it with spins of soaked newspaper or soft rope. Bear in mind to always fill the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealer can crack rather early if you do not take into account this activity before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also conveniently offered on the marketplace. It is a good idea to fit the floor tiles utilizing water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were shown that article about Installing A Bathtub through someone on a different web property. Sharing is good. One never knows, you might be doing someone a favor. Thanks a bunch for your time. Visit us again soon.
Schedule Today
Report this page